Troubleshoot and Fix Black Screen Issues on Windows 10

It can be very annoying when you’re working on an important project, and suddenly the screen goes blank. According to some people, the only possible fix is to wait for the screen to go back to normal. Well, you can’t sit for hours gazing at your screen and trying to figure out what went wrong.

A blank screen also means that you won’t see any error message, which makes it hard to know the root of the cause. A screen suddenly going blank can have many reasons, such as driver update, installation process, buggy system, etc.

It is essential to troubleshoot the black screen issue and fix the same on your Windows 10. Therefore, below is a guide on the instructions to follow when the screen goes black.

Fix Black Screen by Checking for Connectivity Issues 

Hardware and software or both of them can be a cause of desktop screens turning black. Thus, below are the methods to fix the same.

Check Connectivity Issues

In case you haven’t signed in your account and the black screen appears, display connection might be the cause behind the same. To fix this issue, make sure that the signal cable is connected correctly to the right port. You can also try removing and then re-connecting the cable. Also, confirm that the power button is turned on.

Many times, updating BIOS can disable the video card settings. Thus, you can double-check and enable the same in the motherboard settings, if it’s disabled.

Another reason for a black screen can be low brightness. Increase the brightness of your PC or laptop if that’s the case.

Detect Display

A lost connection of display with Windows 10 can be another reason for a black screen. To restart the video driver, press ‘Windows + ctrl + Shift + b’ keys on your keyboard.

If you’re using a tablet, simultaneously press up and down volume buttons up to three times to wake up the screen.

If this method doesn’t work, turn off your device and restart the same after a few seconds to refresh the connectivity.

Following the commands mentioned above will re-establish the link between the display and Windows 10.

Disconnect External Devices

External devices may be the reason behind the black screen. It is advised to remove all the peripheral devices that are not required, such as printers, USB devices, etc.

Once you remove the non-essential devices, start your PC and check if the desktop is working correctly or not. If it does, one of the external devices was inevitably creating an issue.

Fix Black Screen Using Desktop Access on Windows 10

If you see your desktop screen going black after you’ve signed into Windows 10, the Windows Explorer is likely to create an issue here.

The steps to resolve Windows Explorer issues are:

  1. Go to the ‘Task Manager’ by using the keyboard shortcut ‘Ctrl + Shift + Esc.’
  2. Tap on the ‘More Details’ option.
  3. Go to the ‘Processes’ tab.
  4. Locate the ‘Windows Explorer’ service and click on the same.
  5. Hit the ‘Restart’ button at the bottom-right corner of the screen.

In case the steps mentioned above don’t work, discontinue the process and start all over again. The steps to do the same are:

  1. Go to the ‘Task Manager.’
  2. Tap on the ‘More Details’ option.
  3. Right-click on the ‘Windows Explorer’ option, and select ‘End Task’ from the drop-down menu.
  4. Next, click on the ‘File’ menu on the top of the window.
  5. Tap on the ‘Run new task’ option from the pop-up menu.
  6. Enter ‘explorer.exe’ in the given space and press ‘Ok.’

Fix Black Screen Using System Restore on Windows 10

Using the ‘System Restore’ feature has the potential to fix the black screen error. It is important to note that it will only work if the feature is enabled and configured previously. There are two methods to jump to the Advanced Setup before performing System Restore.

Method 1: Use Three Fail-Boot Method

It is impossible to use System Restore, usually when the screen is blank. Therefore, you’ll have to access the startup manually. The steps to do the same are:

  1. Turn on your PC.
  2. Press the power button as soon as you see the Windows logo on your desktop.
  3. Repeat the first two steps up to three times.

Advanced Startup will open automatically after the third interruption.

Method 2: Use the Bootable Media Method

USB Bootable Media method is an alternative to the three fail-boot method. The steps to open Advanced Startup settings are:

  1. Use USB Bootable media to start your PC.
  2. Hit the ‘Next’ button.
  3. Select the ‘Repair your Computer’ option at the bottom of the window.

Now is the time to carry on with your System Restore settings once you’ve opened the Advanced Startup settings.

The steps to restore your computer to fix the black screen are:

  1. Go to the ‘Advanced Startup’ option.
  2. Click on the ‘Troubleshoot’ option.
  3. Select the ‘Advanced Options.’
  4. Select ‘System Restore’ from the menu.
  5. A new dialog box will appear. Hit the ‘Next’ button.
  6. Select any working restore point that might fix the issue.
  7. Tap on the ‘Scan for affected programs’ to know which apps will be affected after creating the restore point.
  8. Click ‘Close.’
  9. Hit the ‘Next’ and ‘Finish’ button respectively to restore.

Following the steps mentioned above is a potential solution to fix the black screen error on your Windows 10.

Cynthia Strickland is a innovative character who has been writing blogs and articles about cyber security. She writes about the state-of-the-art updates involving mcafee.com/activate and how it can enhance the work ride of users. Her articles have been posted in many famous e-magazines, blogs and websites.

Leave a Reply

Your email address will not be published. Required fields are marked *